Not Available in The U.S.
This product is no longer offered by Intepro Systems in the United States. Should you need technical assistance, we will continue to support our products through our support section.
DC Load
High Power Programmable Regenerative DC Load (DISCONTINUED)
The Intepro (DISCONTINUED) Electronic Load is an enhancement of the ELR 9000, offering a new wide ranging mains connection of 360V-528V and increased power density. A single 3U chassis houses 5kW, 10k, or 15kW.
ELR 9000 HP DC Load
These devices incorporate four common regulation modes: constant voltage, constant current, constant power and constant resistance. The FPGA based control circuit provides additional features, such as a function generator, a table-based regulation circuit for the simulation of non-linear internal resistance.
he energy recovery function converts the supplied DC energy into a synchronous sine current and feeds it back into the local grid. This eliminates the usual heat dissipation to a minimum and saves energy costs at the same time. The large color TFT touch panel offers a different and intuitive kind of manual operation, compared to other devices.
Response times for the control via analog or digital interfaces have been improved by the FPGA controlled hardware. In parallel operation of multiple devices, a master-slave bus is used to connect over 64 units in parallel for over 1MW.
User Manuals & Datasheet
Manuals & Datasheets
Features
Key Features of the High Power Programmable Regenerative DC Load (DISCONTINUED) products
Energy Recovery
Recover supplied DC energy into local or public grid
Wide Ranging AC Mains
Accepts 360-528 VAC, 2/3 Phase, 45-66 Hz
Function Generator
User profiles, true function generator
AFV-P Series
Parallel Connection
Master-slave bus for parallel connection
SCPI
SCP command language supported
USB Connectivity
Extra USB port on the front for USB stick
Input Currents
Up to 510 A per chassis
Input Voltage
Up to 1500 V
Expandable
Up to 480kW or more
Regenerative Load Cycle
Recovery
Reduces operational cost
The most important feature of the ELR series is that the AC input, i.e. grid connection, is also used as the output to recover loaded energy with approximately 95% efficiency. Recovering loaded energy reduces energy costs and avoids expensive cooling systems that are commonly required for conventional air-cooled and water-cooled loads that dissipate energy in the form of heat.
ELR9000HP
Regenerative load back to the grid
The standard regenerative function converts the supplied DC energy into a synchronous sine wave current and feeds it back into the local or public grid. This eliminates the usual heat dissipation to a minimum and saves energy costs at the same time.
The large LCD touch panel offers a modern and intuitive user interface for controlling the four operating modes, Constant Voltage (CV), Constant Current (CC), Constant Power (CP) and Constant Resistance (CR). Response times for the control via analog or digital interfaces by the DSP controlled hardware are among the fastest in the industry. In parallel operation of multiple devices, a master-slave bus is used to connect the chassis to create a high power system where the actual values are totaled and the set values distributed.
Wide range of Voltage, Current, Wattage
The available voltage range portfolio for the ELR 9000 HP programmable load goes from models with 0…80 V DC up to models with 0…1500 V DC. Input currents up to 510 amps per chassis are also available. The series offers three power classes with 5 kW, 10 kW or 15 kW in a compact 3U package, which can be extended up to 480kW (or higher) in cabinets for a significantly higher total current. Please contact Intepro systems for higher power solutions.
HMI
Operation (HMI)
Manual operation is done with a Gorilla glass touch panel, two rotary knobs and a push-button. The large color display shows all relevant set values and actual values at a glance.
The whole setup is also done with the human-machine interface, as well the configuration of functions (square, triangle, sine) etc. The display is multilingual (German, English, Russian, Chinese).
ELR9000HP
Share Bus
The “Share Bus” is an analog connection at the rear of the devices and is used to balance current across multiple similar units in parallel connection, such as with loads of this series and series ELR 9000.
It can also be used to build a two-quadrants system in connection with our PSI 9000, PS 9000 and PSB 9000 Series DC Supplies. This system is dedicated for testing purposes using the source-sink principle.
Battery Test & MPP Tracking
For purposes of testing all kinds of batteries, such as for example constant current or constant resistance discharging, the devices offer a battery test mode. This mode shows extra values for elapsed testing time and consumed capacity (Ah). For more detailed setup, there is also an adjustable threshold to stop the battery test on low battery voltage, as well an adjustable maximum test period.
In order to simulate a solar inverter, the devices feature a function called “MPP tracking”, which is used to track and find the MPP (maximum power point) of the connected solar panel.
Remote Control
Remote Control & Connectivity
As for remote control, there are by default two interface ports (1x analog, 1x USB) available on the rear of the devices, which can also be extended by optional, pluggable and retrofittable, digital interface modules (dedicated slot).
Alternatively to the interface modules slot, all models can be equipped with option 3W (see below), which then offers 1x GPIB/IEEE, 1x USB and 1x Analog on the rear side of the device.
For the implementation into the LabView IDE we offer ready-to-use components (VIs) to be used with USB, RS232, GPIB and Ethernet. Other IDEs and interfaces may be supported upon request.
Windows users can profit from the free software “Power Control”. It offers a feature called “Sequencing”, where the device is controlled through a semi-automatic table in CSV format. This table represents a simple test procedure and can be created and edited in MS Excel or other CSV editors and then imported into the software tool.
This software also allows for the control of up to 20 units at once with an optional feature called “Multi Control” (licensed, not free of charge).
Offering Superior Technology & Support
Our Request a Quote system automatically gets sent to our sales team, who review your request and find the right person to answer your questions about our AC Sources, DC Power Supplies, or ATE Test Systems, or other software or equipment we offer that you have questions about
